{"title":"Camshaft \u0026 VVT Components","description":"\u003cp\u003eBrand new camshaft adjusters, VVT solenoids and oil control valves. Direct OEM replacement for a wide range of petrol engines.\u003c\/p\u003e","products":[{"product_id":"camshaft-adjuster-valve-fits-vw-golf-20-04-to-16-ina-06f109257a-06f109257c-new","title":"Camshaft Solenoid Valve – VW Golf – 2004-2016 – 06F109257A","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a cam timing valve or VVT solenoid — on the Volkswagen Golf with this OEM-spec direct fit. Matching part numbers 06F109257A, 06F109257C, 100652, T1066 and TS1066. Also fits equivalent Audi, Skoda and Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283760488792,"sku":"188","price":44.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU188_06F109257A-4_updated_9d4bed70-1bf5-4c96-a904-87c09cd0b367.jpg?v=1781000345"},{"product_id":"for-audi-a4-b8-quattro-camshaft-variable-timing-solenoid-06e109257p-06e109257f","title":"Camshaft Solenoid Valve – Audi A4 B8 – 06E109257P","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (cam timing valve \/ VVT solenoid) restores smooth variable valve timing and full engine performance on the Audi A4 B8 Quattro Camshaft Variable. Built to OEM specification and matching part numbers 06E109257P, 06E109257F, 06E109257J, 06E109257 and 06E109257G. Also fits equivalent Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283768451416,"sku":"150","price":53.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU150_06E109257P-10_updated_944d6e10-1ac8-4e90-88ac-ac860b942558.jpg?v=1780940885"},{"product_id":"for-hyundai-i10-i20-i30-camshaft-variable-timing-valve-intake-2435503011","title":"Camshaft Solenoid Valve – Hyundai i10 i20 i30 – 2435503011","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a VVT solenoid or camshaft solenoid — on the Hyundai I10 I20 I30 Camshaft Variable with this OEM-spec direct fit. Matching part numbers 24355-03011, 24355, 03011, 24355-03011L and 24335-03011.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector. Position: Direct Replacement.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283770941784,"sku":"134","price":57.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU134_24355-03011-3_updated_ab00ad18-89ff-42db-b1c6-b8f39b945640.jpg?v=1780938342"},{"product_id":"renault-megane-16-16v-camshaft-dephaser-timing-solenoid-valve-vvt-8200413185","title":"Camshaft Solenoid Valve – Renault Megane – 8200413185","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (camshaft phaser solenoid \/ cam timing valve) restores smooth variable valve timing and full engine performance on the Renault Megane. Built to OEM specification and matching part numbers 82002-40058, 82004-13185, 8200823650, 823650 and 8200178951.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283786998104,"sku":"169","price":44.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU169_8200240058-4_updated_879c349e-e5f9-4e29-a885-fd18857997a7.jpg?v=1780949117"},{"product_id":"cam-timing-oil-control-valve-vvt-for-lexus-is-200-300-20-1999-05-15330-70011","title":"Camshaft Solenoid Valve – Lexus IS200 IS300 – 1999-2005 – 1533070011","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Lexus IS 200 300 (1999–2005) with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft phaser solenoid, cam timing valve or VVT solenoid. Built to OEM specification and matching part numbers 15330-70010, 15330-70011 and 229700-0150. Also fits equivalent Toyota models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283811836248,"sku":"115","price":65.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU115_15330-70011-7_updated_a1d1fab3-c4d8-4f3a-843c-4aed4c616828.jpg?v=1780924664"},{"product_id":"vvt-solenoid-camshaft-adjuster-valve-for-mazda-2-15-mzr-zj3814420a-2011-15","title":"Camshaft Solenoid Valve – Mazda 2 – 2011-2015 – ZJ3814420A","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Mazda 2 (2011–2015) with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft phaser solenoid, cam timing valve or VVT solenoid. Built to OEM specification and matching part numbers ZJ3814420A and 7473-11350.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283812032856,"sku":"111","price":57.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU111_ZJ3814420A-9_updated_508ddc6e-830c-425f-a96f-85dc8cfb9be3.jpg?v=1780922371"},{"product_id":"camshaft-position-valve-solenoids-side-for-vauxhall-insignia-12578518-12655421","title":"Camshaft Solenoid Valve – Vauxhall Insignia – 12578518","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (vanos solenoid \/ variable valve timing solenoid) restores smooth variable valve timing and full engine performance on the Vauxhall Insignia. Built to OEM specification and matching part numbers 12578518, 12628348, 12646784, 12655421 and 4805106. Also fits equivalent Chevrolet and Saab models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283813704024,"sku":"174","price":45.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU174_03C906455A-7_updated_5cb10219-b9a1-4358-8e81-fb81bdc561fd.jpg?v=1780949437"},{"product_id":"vanos-camshaft-solenoid-valve-for-bmw-m5-535i-550i-activehybrid-f10-11368605123","title":"Camshaft Solenoid Valve – BMW M5 535i 550i ActiveHybrid F10 – 11368605123","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your BMW M5 535I 550I Activehybrid F10 with this direct-replacement VVT camshaft valve position sensor — also known as the variable valve timing solenoid, camshaft phaser solenoid or cam timing valve. Built to OEM specification and matching part numbers 11368605123, 11367610060, 11367585776, 11367561265 and 11367851299.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283813933400,"sku":"117","price":45.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU117_11368605123-7_1_updated_85de7d28-1922-4b30-a577-74aac3bc7032.jpg?v=1780925157"},{"product_id":"camshaft-oil-control-adjuster-valve-for-nissan-note-16-12-2006-on-23796ed00d","title":"Camshaft Solenoid Valve – Nissan Note – 2006-on – 23796ED00D","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a vanos solenoid or variable valve timing solenoid — on the Nissan Note (2006 onwards) with this OEM-spec direct fit. Matching part numbers 23796-ED000, 23796-ED00B, 23796-ED00D, OCV6309 and V38-0280.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283814261080,"sku":"198","price":55.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU198_23796ED000-9_updated_7dd5bc9a-0aa4-4545-9743-ee2ee288858b.jpg?v=1781013215"},{"product_id":"fits-bmw-1-3-5-6-7-series-x1-x3-x5-timing-vanos-solenoid-vvt-camshaft-adjustment","title":"Camshaft Solenoid Valve – BMW 1 3 5 6 7 Series X1 X3 X5 – 11367560462","description":"\u003cp\u003eGet your BMW 1 3 5 6 7 Series back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the variable valve timing solenoid or camshaft phaser solenoid. Built to OEM specification, matching 11367560462, 11360410035, 11361707323, 11360149817 and 7560462.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283815637336,"sku":"176","price":50.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU176_11367560462-10_updated_b5b6be24-e05e-483e-99f4-5556e912b6dd.jpg?v=1780949666"},{"product_id":"for-kia-soul-ceed-rio-upto-2017-camshaft-variable-solenoid-valve-24355-2b700","title":"Camshaft Solenoid Valve – Kia Soul Ceed Rio – 243552B700","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a camshaft phaser solenoid or cam timing valve — on the Kia Soul Ceed RIO with this OEM-spec direct fit. Matching part numbers V530086, 24355, 2B700, 243552B700 and UPTO-2017. Also fits equivalent Hyundai models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283820061016,"sku":"114","price":50.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU114_24355-2B700-8_updated_48e0e528-e2ea-4385-87d8-359e7e7a09ff.jpg?v=1780924543"},{"product_id":"for-hyundai-i30-2008-2017-camshaft-variable-timing-solenoid-valve-oil-243552b000","title":"Camshaft Solenoid Valve – Hyundai i30 – 2008-2017 – 243552B000","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a vanos solenoid or variable valve timing solenoid — on the Hyundai I30 (2008–2017) with this OEM-spec direct fit. Matching part numbers 24355, 2B000 and 243552B000. Also fits equivalent Kia models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283821142360,"sku":"112","price":45.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU112_24355-2B000-3_updated_14b41348-e564-4f42-8a9b-adf25f452279.jpg?v=1780922441"},{"product_id":"camshaft-timing-oil-control-valve-for-nissan-note-12-e12-2012-16-23796-3hd2a","title":"Camshaft Solenoid Valve – Nissan Note E12 – 2012-2016 – 237963HD2A","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a cam timing valve or VVT solenoid — on the Nissan Note (2012–2016) with this OEM-spec direct fit. Matching part numbers 23796-3HD2A, 23796-3HD0A and 23796.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283822584152,"sku":"131","price":70.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU131_23796-3HD2A-4_updated_72a7fe0b-d846-4b40-b602-9ab4e90fe2f9.jpg?v=1780932341"},{"product_id":"camshaft-solenoid-valve-vvt-for-toyota-corolla-e12-1618-vvt-i-15330-22030","title":"Camshaft Solenoid Valve – Toyota Corolla E12 – 1533022030","description":"\u003cp\u003eGet your Toyota Corolla E12 back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the oil control valve (OCV) or vanos solenoid. Built to OEM specification, matching 15330-22030 and 15330-22010.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283823239512,"sku":"148","price":53.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU148_15330-22030-9_updated_af36b7b7-8bce-4035-88ad-c9625d55c02b.jpg?v=1780940666"},{"product_id":"exhaust-camshaft-variable-solenoid-valve-24375-03010-vvt-for-hyundai-i10-i20","title":"Camshaft Solenoid Valve – Hyundai i10 i20 – 2437503010","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called an oil control valve (OCV) or vanos solenoid — on the Hyundai I10 I20 with this OEM-spec direct fit. Matching part numbers 24375-03010 and THYU24375-03010. Also fits equivalent Kia models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283824550232,"sku":"118","price":47.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU118_24375-03010-11_updated_ea56ae64-ca47-4d7c-ae47-edf4132d6c7e.jpg?v=1780925313"},{"product_id":"intake-vvt-vanos-solenoid-valve-for-ford-smax-mk1-20-ecoboost-2006-14-36001878","title":"Camshaft Solenoid Valve – Ford S-Max Mk1 – 2006-2014 – 36001878","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (VVT solenoid \/ camshaft solenoid) restores smooth variable valve timing and full engine performance on the Ford Smax MK1 (2006–2014). Built to OEM specification and matching part numbers 5116028, BB5E-6M280-AB, AJ813114, LR024995 and 36001878. Also fits equivalent Jaguar, Volvo and Land Rover models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283827990872,"sku":"151","price":60.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU151_BB5E-6M280AB-8_updated_fa7dc2f6-dc2f-441b-9304-84687ec6faae.jpg?v=1780942027"},{"product_id":"brand-new-oil-control-valve-fits-subaru-forester-20-25-10921aa080-2008-2018","title":"Camshaft Solenoid Valve – Subaru Forester – 2008-2018 – 10921AA080","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Subaru Forester (2008–2018) with this direct-replacement VVT camshaft valve position sensor — also known as the variable valve timing solenoid, camshaft phaser solenoid or cam timing valve. Built to OEM specification and matching part numbers 10921AA080.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283831398744,"sku":"173","price":70.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU173_10921AA080_-8_updated_44a9d678-df16-4725-86e1-a41cdab6b373.jpg?v=1780949354"},{"product_id":"new-vvt-vanos-solenoid-valve-inlet-for-toyota-iq-j1-133-2009-15-1533047010","title":"Camshaft Solenoid Valve – Toyota iQ J1 – 2009-2015 – 1533047010","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (camshaft phaser solenoid \/ cam timing valve) restores smooth variable valve timing and full engine performance on the Toyota IQ J1 1.33 (2009–2015). Built to OEM specification and matching part numbers 153300Y010, 15330-47010, 15330-0Y050, A70-0355 and 716042. Also fits equivalent Aston martin, Daihatsu and Subaru models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283831660888,"sku":"105","price":49.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU105_15330-0Y010_15330-47010_-2_updated_ce1d3740-e1d4-4250-b4d7-ea247ed25c87.jpg?v=1780919190"},{"product_id":"exhaust-vvt-camshaft-adjuster-valve-for-volvo-xc90-i-25t-t6-2002-14-31355829","title":"Camshaft Solenoid Valve – Volvo XC90 I – 2002-2014 – 31355829","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (cam timing valve \/ VVT solenoid) restores smooth variable valve timing and full engine performance on the Volvo XC90 I 2.5t T6 (2002–2014). Built to OEM specification and matching part numbers 31355829, 31355829S1, 36002146, 36002146S1 and 36002686.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283832447320,"sku":"106","price":75.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU106_31355829-8_updated_963902cb-06c5-408e-b20a-348c32c42a6e.jpg?v=1780919629"},{"product_id":"control-valve-camshaft-adjustment-for-toyota-yarisvitz-10-1999-05-15330-23010","title":"Camshaft Solenoid Valve – Toyota Yaris Vitz – 1999-2005 – 1533023010","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Toyota Yaris\/vitz (1999–2005) with this direct-replacement VVT camshaft valve position sensor — also known as the VVT solenoid, camshaft solenoid or oil control valve (OCV). Built to OEM specification and matching part numbers 15330-23010, 15330-0J010 and 229700-0290.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283832643928,"sku":"103","price":55.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU103_229700-0290-9_updated_154e41e0-eb62-4d42-b627-99aa26d59b30.jpg?v=1780918402"},{"product_id":"new-intake-vvt-vanos-solenoid-valve-for-ford-s-max-1516-ecoboost-2011-18","title":"Camshaft Solenoid Valve – Ford S-Max – 2011-2018 – 1319633","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Ford S-max (2011–2018) with this direct-replacement VVT camshaft valve position sensor — also known as the cam timing valve, VVT solenoid or camshaft solenoid. Built to OEM specification and matching part numbers 1319633, 1331496, 1366327, 1793455 and 1871405.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283832807768,"sku":"104","price":43.5,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU104_CN1G6L713AC-6_updated_59b3d34c-552b-4c2e-87fd-cec20836a8fd.jpg?v=1780918627"},{"product_id":"camshaft-control-valve-solenoid-fits-audi-a6-c6-2832-fsi-30-tfsi-06e109257l","title":"Camshaft Solenoid Valve – Audi A6 C6 – 06E109257L","description":"\u003cp\u003eGet your Audi A6 C6 back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the vanos solenoid or variable valve timing solenoid. Built to OEM specification, matching 06E109257L, 06E109257, 716085, KT3016 and 11091777801.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283833823576,"sku":"166","price":47.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU166_06E109257L-5_updated_22278054-40b2-4763-957c-2afd200e9b72.jpg?v=1780948620"},{"product_id":"new-camshaft-adjuster-valve-intake-fits-volvo-s40-ii-v50-24t5-31216221-2004-12","title":"Camshaft Solenoid Valve – Volvo S40 II V50 – 2004-2012 – 31216221","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a camshaft phaser solenoid or cam timing valve — on the Volvo S40 II V50 2.4\/t5 (2004–2012) with this OEM-spec direct fit. Matching part numbers 6M5G-6L713-AB, 1478181, 36002687, 31216221 and 381180002. Also fits equivalent Ford models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283833921880,"sku":"109","price":50.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU109_31216221-8_updated_1e11b5bd-e22f-48f3-a943-dd25e02e5bd1.jpg?v=1780920546"},{"product_id":"exhaust-side-vvt-vanos-solenoid-valve-for-ford-focus-iii-16-tilpg-4m5g6l713be","title":"Camshaft Solenoid Valve – Ford Focus III – 4M5G6L713BE","description":"\u003cp\u003eGet your Ford Focus III back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the oil control valve (OCV) or vanos solenoid. Built to OEM specification, matching CN1G6L713BC, 6L713BC, 554007, 1319634 and 1331497.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283834347864,"sku":"142","price":46.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU142_CN1G6L713BC-2_updated_2fbbaeea-d4ba-44a7-887b-555c9d357cca.jpg?v=1780940032"},{"product_id":"for-vw-golf-mk7-20-gticlubsport-20r-18-tsi-2012-on-camshaft-adjuster-valve","title":"Camshaft Solenoid Valve – VW Golf Mk7 – 2012-on – 06E103697AE","description":"\u003cp\u003eGet your Volkswagen Golf MK7 (2012 onwards) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the oil control valve (OCV) or vanos solenoid. Built to OEM specification, matching 06E103697AE, 06E103697L, 06E103697K, 06E103697M and 06E103697H. Also fits equivalent Audi models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283834478936,"sku":"110","price":50.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU110_06E103697K-5_updated_6dd2b9cd-71b0-4aa4-b70b-ae297f51c796.jpg?v=1780921887"},{"product_id":"intake-camshaft-adjuster-valve-fits-hyundai-ix20-ix35-14-16-2010-on-243552b600","title":"Camshaft Solenoid Valve – Hyundai ix20 ix35 – 2010-on – 243552B600","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Hyundai IX20 IX35 (2010 onwards) with this direct-replacement VVT camshaft valve position sensor — also known as the cam timing valve, VVT solenoid or camshaft solenoid. Built to OEM specification and matching part numbers 24355-2B600, A53-0120, 716039, KT3030 and OCV3605. Also fits equivalent Kia models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283834610008,"sku":"186","price":45.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU186_24355-2B600-9_updated_1f225e1d-9852-4b68-934b-c661ccae7c8e.jpg?v=1780999792"},{"product_id":"toyota-verso-camshaft-solenoid-valve-variable-valve-timing-15330-37010-oil-valve","title":"Camshaft Solenoid Valve – Toyota Verso – 1533037010","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (vanos solenoid \/ variable valve timing solenoid) restores smooth variable valve timing and full engine performance on the Toyota Verso Camshaft. Built to OEM specification and matching part numbers 15330-0T010, 15330-37010, 15330-0T030, 15330-0T040 and 15330-0T020. Also fits equivalent Lexus models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283834773848,"sku":"164","price":46.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU164_15330-37010-8_updated_b7a68ae9-c20c-4a41-8017-1e717625fcf2.jpg?v=1780948493"},{"product_id":"new-camshaft-timing-solenoid-valve-for-peugeot-208-i-12-thp-110-9675081780","title":"Camshaft Solenoid Valve – Peugeot 208 I – 9675081780","description":"\u003cp\u003eGet your Peugeot 208 I back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the cam timing valve or VVT solenoid. Built to OEM specification, matching 9675081780, 3639832, SU001-A9195, 716109 and 381180016. Also fits equivalent Citroën, DS and Opel models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283834937688,"sku":"101","price":49.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU101_1c201b019f8b30075b650a04f33d21003370ce28_updated_cafe1c28-32b8-4268-964b-b41a77380a4c.jpg?v=1780917499"},{"product_id":"camshaft-adjuster-valve-outlet-fits-toyota-yarisvitz-p13-13-p9-133-2008-on","title":"Camshaft Solenoid Valve – Toyota Yaris Vitz P13 P9 – 2008-on – 1533047020","description":"\u003cp\u003eGet your Toyota Yaris\/vitz P13 (2008 onwards) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the camshaft phaser solenoid or cam timing valve. Built to OEM specification, matching 15330-47020, 15330-0Y060, 381180028, 8091533 and 17358. Also fits equivalent Aston martin, Daihatsu and Subaru models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"SilverHub","offers":[{"title":"Default Title","offer_id":57283838116184,"sku":"144","price":47.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU144_15330-47020-5_updated_d527cac1-990d-47ec-a4ed-b11203c8b31f.jpg?v=1780940207"},{"product_id":"vvt-camshaft-adjuster-valve-for-toyota-supra-30ii-biturbo-1993-02-1533046011","title":"Camshaft Solenoid Valve – Toyota Supra – 1993-2002 – 1533046011","description":"\u003cp\u003eGet your Toyota Supra 3.0i\/i BiTurbo (1993–2002) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the oil control valve (OCV) or vanos solenoid. Built to OEM specification, matching 15330-46011. Also fits equivalent Lexus models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283838280024,"sku":"136","price":80.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU136_15330-46011-4_updated_cf090754-6d92-41df-b5ab-f60f81eb3c7e.jpg?v=1780939240"},{"product_id":"camshaft-adjuster-valve-fits-opel-vauxhall-insignia-a-28-v6-2007-17-12636175","title":"Camshaft Solenoid Valve – Vauxhall Insignia A – 2007-2017 – 12636175","description":"\u003cp\u003eGet your Opel Insignia A (2007–2017) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the VVT solenoid or camshaft solenoid. Built to OEM specification, matching 12586722, 12636175, 12588943, 12615613 and 12626012. Also fits equivalent Cadillac, Chevrolet and Saab models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283838673240,"sku":"102","price":42.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU102_12636175-2_updated_18da192c-ae3d-432e-9de4-49edd6d24fca.jpg?v=1780917584"},{"product_id":"vvt-vanos-camshaft-adjuster-valve-for-ford-focus-20-st-23-rs-cj5e6b297aa","title":"Camshaft Solenoid Valve – Ford Focus ST RS – CJ5E6B297AA","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Ford Focus with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft solenoid, oil control valve (OCV) or vanos solenoid. Built to OEM specification and matching part numbers CJ5E-6B297-AA, CJ5Z-6M280-A, CJ5E-6B297-AB, 2026089 and 5146080.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283838968152,"sku":"107","price":48.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU107_CJ5E6B297AA-7_updated_30a3192e-b9ed-40c5-b2dc-6e8afb1031a0.jpg?v=1780919866"},{"product_id":"toyota-avensis-16-18-2008-18-camshaft-adjustment-valve-outlet-15330-37020","title":"Camshaft Solenoid Valve – Toyota Avensis – 2008-2018 – 1533037020","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a vanos solenoid or variable valve timing solenoid — on the Toyota Avensis (2008–2018) with this OEM-spec direct fit. Matching part numbers 15330-0T020, 15330-37020, 381180021, WG1741921 and WG1807521. Also fits equivalent Lexus models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283839131992,"sku":"138","price":45.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU138_15330-37020-7_updated_99f67d12-d1f4-4322-9616-4bc32294e42a.jpg?v=1780939466"},{"product_id":"camshaft-adjustment-control-valve-fits-audi-a1-10-14-tfsi-04e906455d-2012-18","title":"Camshaft Solenoid Valve – Audi A1 – 2012-2018 – 04E906455D","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (camshaft solenoid \/ oil control valve (OCV)) restores smooth variable valve timing and full engine performance on the Audi A1 (2012–2018). Built to OEM specification and matching part numbers 04E906455, 04E906455D, 04E906455N, 04E906455AC and 2800014002180.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283839295832,"sku":"183","price":42.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU183_04E906455D-4_updated_95ff8e34-518b-4302-843c-335a1c1ae687.jpg?v=1780998378"},{"product_id":"vvt-vanos-camshaft-adjuster-valve-for-peugeot-107-10-2005-14-1920hz-1920kr","title":"Camshaft Solenoid Valve – Peugeot 107 – 2005-2014 – 1533040020","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a variable valve timing solenoid or camshaft phaser solenoid — on the Peugeot 107 (2005–2014) with this OEM-spec direct fit. Matching part numbers 15330-40020, 15330-0Q010, 1920HZ and 1920KR. Also fits equivalent Citroën and Toyota models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283839361368,"sku":"140","price":52.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU140_15330-40020-7_updated_26540225-be14-469a-9ac2-85211beaa006.jpg?v=1780939670"},{"product_id":"camshaft-adjuster-valve-fits-audi-a8-d4-253040-tfsi-s8-06e109257t-2010-18","title":"Camshaft Solenoid Valve – Audi A8 D4 S8 – 2010-2018 – 06E109257T","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (variable valve timing solenoid \/ camshaft phaser solenoid) restores smooth variable valve timing and full engine performance on the Audi A8 D4 (2010–2018). Built to OEM specification and matching part numbers 06E109257, 06E109257T, 06E109257S, 06E109257N and 06E109257M. Also fits equivalent Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283839656280,"sku":"178","price":47.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU178_06E109257T-2_updated_07712574-5445-46ad-afc9-575e16c27094.jpg?v=1780994777"},{"product_id":"new-control-valve-camshaft-adjustment-fits-ford-s-max-20-2010-14-6m8g6m280","title":"Camshaft Solenoid Valve – Ford S-Max – 2010-2014 – 6M8G6M280AA","description":"\u003cp\u003eGet your Ford S MAX (2010–2014) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the cam timing valve or VVT solenoid. Built to OEM specification, matching 6M8G-6M280, L3K9-14-420A, L309-14-420A, LR025652 and XR858494. Also fits equivalent Mazda, Jaguar and Land Rover models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283839754584,"sku":"155","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU155_L309-14-420-9_updated_1b7df545-59af-4a2b-8e20-ba14976e50fb.jpg?v=1780942390"},{"product_id":"camshaft-timing-oil-control-valve-for-vauxhall-viva-c16-10-2015-18-12671373","title":"Camshaft Solenoid Valve – Vauxhall Viva C16 – 2015-2018 – 12671373","description":"\u003cp\u003eGet your Vauxhall Viva C16 (2015–2018) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the variable valve timing solenoid or camshaft phaser solenoid. Built to OEM specification, matching 1235132, 1235132S1, 12671373, 12671373S1 and 12636524.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283839918424,"sku":"171","price":54.5,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU171_12636524-8_updated_7803cdf9-2246-4346-a357-0a361b1e66a5.jpg?v=1780949252"},{"product_id":"new-camshaft-adjuster-valve-outlet-fits-volvo-s40-ii-v50-24t5-31216222-2004-12","title":"Camshaft Solenoid Valve – Volvo S40 II V50 – 2004-2012 – 31216222","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (vanos solenoid \/ variable valve timing solenoid) restores smooth variable valve timing and full engine performance on the Volvo S40 II V50 2.4\/t5 (2004–2012). Built to OEM specification and matching part numbers 6M5G-6L713-BB, 30731282, 31216222, 36002688 and 8692993. Also fits equivalent Ford models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283840016728,"sku":"108","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU108_31216222-2_updated_89598b8d-35e9-44b2-87e1-4a9ad59624b2.jpg?v=1780920120"},{"product_id":"camshaft-adjustment-control-valve-fits-toyota-previa-estima-ii-iii-24-2000-on","title":"Camshaft Solenoid Valve – Toyota Previa Estima II III – 2000-on – 1533028020","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (vanos solenoid \/ variable valve timing solenoid) restores smooth variable valve timing and full engine performance on the Toyota Previa Estima II III (2000 onwards). Built to OEM specification and matching part numbers 15330-28020, A70-0346, 716015, KT3036 and OCV9101.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283840967000,"sku":"146","price":42.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU146_15330-28020-2_updated_e46f9fa4-ab57-4818-8026-215e9cbf06db.jpg?v=1780940347"},{"product_id":"camshaft-adjuster-valve-fits-honda-cr-v-mk-ii-20-2001-07-15830-rbb-003","title":"Camshaft Solenoid Valve – Honda CR-V Mk II – 2001-2007 – 15830RBB003","description":"\u003cp\u003eGet your Honda Cr-v MK II (2001–2007) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the cam timing valve or VVT solenoid. Built to OEM specification, matching 15830-PNC-003, 15830-PNB-003, 15830-PNA-003, 15830-RBB-003 and 15830-RAD-Y01.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283841065304,"sku":"184","price":52.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU184_15830PNC003-10_updated_6491928b-b214-4463-89b2-86b23e4a9363.jpg?v=1780998984"},{"product_id":"new-vvt-vanos-camshaft-adjuster-valve-for-toyota-celica-coupe-18-16v-ts-1999-05","title":"Camshaft Solenoid Valve – Toyota Celica – 1999-2005 – 1533022020","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Toyota Celica (1999–2005) with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft phaser solenoid, cam timing valve or VVT solenoid. Built to OEM specification and matching part numbers 5330-22020, 15330-22020 and BAF1810158A.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283841229144,"sku":"132","price":55.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU132_15330-22020-5_updated_c9aee0d1-3e83-44cb-857d-f6ce241e027f.jpg?v=1780932399"},{"product_id":"vvt-vanos-solenoid-valve-fits-nissan-juke-16-dig-t-nismo-23796-ja00a-2013-on","title":"Camshaft Solenoid Valve – Nissan Juke – 2013-on – 23796JA00A","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Nissan Juke (2013 onwards) with this direct-replacement VVT camshaft valve position sensor — also known as the cam timing valve, VVT solenoid or camshaft solenoid. Built to OEM specification and matching part numbers 23796-JA00A, PTA127-0193, A38-0355, V38-0323 and 0899143.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283841458520,"sku":"153","price":57.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU153_23796-JA00A-12_updated_96c656a9-b8fe-4690-9b6c-8ac3c9481be4.jpg?v=1780942241"},{"product_id":"variable-valve-timing-control-for-toyota-yarisvitz-13-15-1999-10-15330-21011","title":"Camshaft Solenoid Valve – Toyota Yaris Vitz – 1999-2010 – 1533021011","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a camshaft solenoid or oil control valve (OCV) — on the Toyota Yaris\/vitz (1999–2010) with this OEM-spec direct fit. Matching part numbers 15330-21011, 15330-21010, 15330-21020, A70-0347 and OCV9104.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283871703384,"sku":"168","price":50.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU168_15330-21011_-10_updated_961b4fa1-b54e-4a56-a79d-48adabddac48.jpg?v=1780949042"},{"product_id":"vvt-vanos-solenoid-camshaft-actuator-inlet-fit-vauxhall-astra-20-vxr-gtc","title":"Camshaft Solenoid Valve – Vauxhall Astra VXR GTC – 1235095","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a cam timing valve or VVT solenoid — on the Vauxhall Astra with this OEM-spec direct fit. Matching part numbers 1235095, 1235116, 12578517, 12628347 and 12646783. Also fits equivalent Alfa romeo, Buick and Chevrolet models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283877962072,"sku":"121","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU121_3_updated_21d2b597-e18b-4f69-a797-d8b2bc783d9e.jpg?v=1780925977"},{"product_id":"camshaft-adjuster-valve-vvs103-gates-1235095-12628347-1235116-12646783-12578517","title":"Camshaft Solenoid Valve – 1235095","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a VVT solenoid or camshaft solenoid — on the Chevrolet with this OEM-spec direct fit. Matching part numbers 1235095, 1235116, 12578517, 12628347 and 12646783. Also fits equivalent Opel, Saab and Vauxhall models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283879240024,"sku":"121","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU121_3_updated_a2384113-a917-413b-88df-9c4b47b1e684.jpg?v=1780925992"},{"product_id":"vvt-vanos-solenoid-valve-cyl-head-inlet-fits-alfa-159-brera-spider-939-301svv","title":"Camshaft Solenoid Valve – Alfa Romeo 159 Brera Spider 939 – 12655420","description":"\u003cp\u003eGet your Alfa romeo back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the cam timing valve or VVT solenoid. Built to OEM specification, matching 12655420, 12646783, 12628347, 12578517 and 012655420.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283880091992,"sku":"121","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU121_3_updated_83fb135c-a3e1-48d9-993b-a92cb124678e.jpg?v=1780927260"},{"product_id":"outlet-timing-vanos-solenoid-camshaft-for-chevrolet-captiva-alfa-romeo-pontiac","title":"Camshaft Solenoid Valve – Chevrolet Captiva Alfa Romeo Pontiac – 12628348","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Chevrolet Captiva Alfa Romeo Pontiac with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft phaser solenoid, cam timing valve or VVT solenoid. Built to OEM specification and matching part numbers 12628348, 12646784, 12655421, 12679100 and 1235095. Also fits equivalent Opel, Saab and Vauxhall models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283880419672,"sku":"116","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU116_2_updated_584797a8-229f-439b-a0d0-722f26ccb1fb.jpg?v=1780924736"},{"product_id":"vvt-vanos-solenoid-valve-exhaust-for-alfa-159-19-22-05-11-939-petrol","title":"Camshaft Solenoid Valve – Alfa Romeo 159 939 – 12628348","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (camshaft phaser solenoid \/ cam timing valve) restores smooth variable valve timing and full engine performance on the Alfa romeo. Built to OEM specification and matching part numbers 12628348, 12646784, 12655421, 12679100 and 1235095.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283881107800,"sku":"116","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU116_2_updated_07b6d2b2-c96c-4e32-8e37-d87d6a995474.jpg?v=1780924751"},{"product_id":"vvt-vanos-solenoid-valve-exhaust-side-fits-vauxhall-antara-astra-insignia-57fc","title":"Camshaft Solenoid Valve – Vauxhall Antara Astra Insignia – 12628348","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a camshaft solenoid or oil control valve (OCV) — on the Vauxhall Antara Astra Insignia 57FC with this OEM-spec direct fit. Matching part numbers 12628348, 12646784, 12655421, 12679100 and 1235095.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283881861464,"sku":"116","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU116_2_updated_7eb41811-ffd3-4f36-be68-fd65cbdb3f86.jpg?v=1780924929"}],"url":"https:\/\/carpartclubs.com\/collections\/camshaft-vvt-components.oembed?page=2","provider":"CarPartClubs","version":"1.0","type":"link"}