{"title":"Chevrolet Captiva Parts","description":"\u003cp\u003eFind replacement parts for the Chevrolet Captiva — including VVT solenoids and fuel pressure sensors. Every part is built to OEM specification and matched to Chevrolet Captiva fitments by part number, so you can order with confidence. We stock 12 Chevrolet Captiva-compatible parts, dispatched from the UK with next-day delivery and a 1-year warranty.\u003c\/p\u003e\u003cp\u003eNot sure if a part fits your Chevrolet Captiva? Send us your registration or VIN and we'll confirm before you order.\u003c\/p\u003e","products":[{"product_id":"fuel-rail-pressure-sensor-for-kia-ceed-venga-rio-14-16-crdi-55pp30-01","title":"Fuel Rail Pressure Sensor – Kia Cee'd Venga Rio – 55PP3001","description":"\u003cp\u003eReplace your failing fuel pressure sensor — also called a fuel rail sensor or fuel rail pressure sensor — on the Kia Cee'd Venga RIO with this OEM-spec direct fit. Matching part numbers 9307Z528A, 55PP30-01, 31400-2A700, R9144Z271A and 96868901. Also fits equivalent Hyundai, Chevrolet and Opel models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283699048792,"sku":"258","price":42.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU258_55PP30-01_-46_updated_5d9e9fc6-fb63-430b-adce-e4e340f87c1e.jpg?v=1781606994"},{"product_id":"new-for-vauxhall-opel-antara-22-cdti-fuel-rail-high-pressure-sensor-55pp30-01","title":"Fuel Rail Pressure Sensor – Vauxhall Antara – 55PP3001","description":"\u003cp\u003eThis direct-fit fuel pressure sensor (FRP sensor \/ fuel pressure transducer) restores correct fuel rail pressure regulation and reliable starting on the Vauxhall Antara. Built to OEM specification and matching part numbers 9307Z528A, 55PP30-01, 31400-2A700, R9144Z271A and 96868901. Also fits equivalent Chevrolet, Hyundai and Kia models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283700949336,"sku":"258","price":42.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU258_55PP30-01_-46_updated_b6992a66-4140-429d-b377-00d8f34a7358.jpg?v=1781607015"},{"product_id":"for-vauxhall-corsa-corsavan-mk3-d-13-cdti-fuel-rail-pressure-sensor-0281002706","title":"Fuel Rail Pressure Sensor – Vauxhall Corsa Corsavan Mk3 D – 0281002706","description":"\u003cp\u003eGet your Vauxhall Corsa Corsavan MK3 D back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the low pressure fuel sensor or fuel rail sensor. Built to OEM specification, matching 0281002706, 0281002937, 504152959, 55195078 and 500372234. Also fits equivalent Alfa romeo, Suzuki and Ford models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283788898648,"sku":"156","price":43.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU156_0281002706-8_updated_e75b1b4f-39ea-4074-b480-8aece2aea801.jpg?v=1780942524"},{"product_id":"camshaft-position-valve-solenoids-side-for-vauxhall-insignia-12578518-12655421","title":"Camshaft Solenoid Valve – Vauxhall Insignia – 12578518","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (vanos solenoid \/ variable valve timing solenoid) restores smooth variable valve timing and full engine performance on the Vauxhall Insignia. Built to OEM specification and matching part numbers 12578518, 12628348, 12646784, 12655421 and 4805106. Also fits equivalent Chevrolet and Saab models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283813704024,"sku":"174","price":45.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU174_03C906455A-7_updated_5cb10219-b9a1-4358-8e81-fb81bdc561fd.jpg?v=1780949437"},{"product_id":"camshaft-adjuster-valve-fits-opel-vauxhall-insignia-a-28-v6-2007-17-12636175","title":"Camshaft Solenoid Valve – Vauxhall Insignia A – 2007-2017 – 12636175","description":"\u003cp\u003eGet your Opel Insignia A (2007–2017) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the VVT solenoid or camshaft solenoid. Built to OEM specification, matching 12586722, 12636175, 12588943, 12615613 and 12626012. Also fits equivalent Cadillac, Chevrolet and Saab models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283838673240,"sku":"102","price":42.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU102_12636175-2_updated_18da192c-ae3d-432e-9de4-49edd6d24fca.jpg?v=1780917584"},{"product_id":"vvt-vanos-solenoid-camshaft-actuator-inlet-fit-vauxhall-astra-20-vxr-gtc","title":"Camshaft Solenoid Valve – Vauxhall Astra VXR GTC – 1235095","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a cam timing valve or VVT solenoid — on the Vauxhall Astra with this OEM-spec direct fit. Matching part numbers 1235095, 1235116, 12578517, 12628347 and 12646783. Also fits equivalent Alfa romeo, Buick and Chevrolet models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283877962072,"sku":"121","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU121_3_updated_21d2b597-e18b-4f69-a797-d8b2bc783d9e.jpg?v=1780925977"},{"product_id":"camshaft-adjuster-valve-vvs103-gates-1235095-12628347-1235116-12646783-12578517","title":"Camshaft Solenoid Valve – 1235095","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a VVT solenoid or camshaft solenoid — on the Chevrolet with this OEM-spec direct fit. Matching part numbers 1235095, 1235116, 12578517, 12628347 and 12646783. Also fits equivalent Opel, Saab and Vauxhall models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283879240024,"sku":"121","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU121_3_updated_a2384113-a917-413b-88df-9c4b47b1e684.jpg?v=1780925992"},{"product_id":"outlet-timing-vanos-solenoid-camshaft-for-chevrolet-captiva-alfa-romeo-pontiac","title":"Camshaft Solenoid Valve – Chevrolet Captiva Alfa Romeo Pontiac – 12628348","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Chevrolet Captiva Alfa Romeo Pontiac with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft phaser solenoid, cam timing valve or VVT solenoid. Built to OEM specification and matching part numbers 12628348, 12646784, 12655421, 12679100 and 1235095. Also fits equivalent Opel, Saab and Vauxhall models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283880419672,"sku":"116","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU116_2_updated_584797a8-229f-439b-a0d0-722f26ccb1fb.jpg?v=1780924736"},{"product_id":"intake-camshaft-adjuster-valve-for-opel-vauxhall-antara-a-24-2006-on-12655420","title":"Camshaft Solenoid Valve – Vauxhall Antara A – 2006-on – 12655420","description":"\u003cp\u003eGet your Opel Antara A (2006 onwards) back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the camshaft phaser solenoid or cam timing valve. Built to OEM specification, matching 12655420, 12646783, 12628347, 12578517 and 012655420. Also fits equivalent Chevrolet and Saab models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283905651032,"sku":"121","price":41.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU121_3_updated_98462dd9-a398-4726-8494-86e2634ff791.jpg?v=1780927279"}],"url":"https:\/\/carpartclubs.com\/collections\/chevrolet-captiva-parts.oembed","provider":"CarPartClubs","version":"1.0","type":"link"}