{"title":"Ford Kuga Parts","description":"\u003cp\u003eFind replacement parts for the Ford Kuga — including VVT solenoids, fuel pressure sensors and oxygen \u0026amp; lambda sensors. Every part is built to OEM specification and matched to Ford Kuga fitments by part number, so you can order with confidence. We stock 17 Ford Kuga-compatible parts, dispatched from the UK with next-day delivery and a 1-year warranty.\u003c\/p\u003e\u003cp\u003eNot sure if a part fits your Ford Kuga? Send us your registration or VIN and we'll confirm before you order.\u003c\/p\u003e","products":[{"product_id":"new-fuel-pressure-control-valve-for-ford-kuga-i-ii-20-tdci-2008-on-9m5q9d347aa","title":"Fuel Pressure Regulator – Ford Kuga I II – 2008-on – 9M5Q9D347AA","description":"\u003cp\u003eGet your Ford Kuga I II (2008 onwards) back to correct fuel rail pressure and stable engine running with this replacement fuel pressure regulator, also referenced in service manuals as the rail pressure regulator or fuel pressure control valve. Built to OEM specification, matching 7701479182, F6800-12103001, 9M5Q-9D347-AA, 9467636180 and 1736080.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure regulator commonly causes hard starting when hot, rough idle, hesitation under acceleration, poor fuel economy, and fault codes P0089, P0190, P0191 or P0192. On some vehicles you'll see fuel leaks at the regulator body, or a strong fuel smell under the bonnet. Common-rail diesels with stuck regulators drop into limp mode under load. Petrol direct-injection engines may also show a rough cold start or misfire codes.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, threaded into the fuel rail or pump body. Relieve fuel pressure before removal and have rags ready to catch residual fuel. Replace any sealing O-rings supplied. After fitting, cycle the ignition to prime, clear codes and test for leaks before driving. Standard 2 pin connector. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this the same as a fuel pressure sensor?\u003c\/h4\u003e\n\u003cp\u003eNo — the sensor measures rail pressure and reports to the ECU. The regulator physically controls rail pressure. Both can fail and produce similar fault codes, so confirm with live data before ordering.\u003c\/p\u003e\n\u003ch4\u003eCan I drive with a failing FPR?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but unregulated fuel pressure damages injectors over time on common-rail diesels and causes excess emissions on petrol engines. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eDo I need to code or programme the new regulator?\u003c\/h4\u003e\n\u003cp\u003eNo — it's a passive hydraulic component. The ECU re-learns rail pressure within a few minutes of running.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283684139352,"sku":"246","price":84.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU246_9M5Q-9D347-AA_-7_updated_10bf53df-cd80-469d-8710-631092dfe542.jpg?v=1781458587"},{"product_id":"fuel-pressure-sensor-fits-ford-focus-ii-25-rs-st-kuga-i-25-2005-12-7m5n9c968aa","title":"Fuel Rail Pressure Sensor – Ford Focus II Kuga I – 2005-2012 – 7M5N9C968AA","description":"\u003cp\u003eGet your Ford Focus II (2005–2012) back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the fuel pressure transducer or high pressure fuel sensor. Built to OEM specification, matching 0261230238, 0261230239, 31251447, 31272732 and 7M5N-9C968-AA. Also fits equivalent Land Rover and Volvo models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 4 pin connector. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283689972056,"sku":"255","price":40.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU255_7M5N-9C968-AA-3_updated_ddc31b41-d376-4e67-a2d8-25930bf97920.jpg?v=1781604338"},{"product_id":"lambda-oxygen-sensor-ford-c-max-focus-mk3-galaxy-kuga-mondeo-mk4-s-max-20-tdci","title":"Oxygen Sensor – After Catalyst – Ford C-Max Focus Mk3 Galaxy Kuga Mondeo Mk4 S-Max – 1747897","description":"\u003cp\u003eGet your Ford C-max Focus MK3 Galaxy Kuga Mondeo back to correct air-fuel mixture, fuel economy and emissions performance with this replacement oxygen sensor, also referenced in service manuals as the lambda sensor or O2 sensor. Built to OEM specification, matching 1747897, 7G91-9D375-AA, 7G919D375BA, AB3A-9Y460-AA and CC1A9Y460AA.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing lambda or oxygen sensor will turn on the check engine light and commonly log fault codes in the P0130–P0167 range (sensor circuit and heater faults). Drivers typically notice a sudden drop in fuel economy, rough or fluctuating idle, hesitation under load, a sulphur or rotten-egg smell from the exhaust, and in many cases an MOT emissions failure. On modern diesels and direct-injection petrols, a stuck or slow-responding sensor can also push the engine into limp mode.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation with the correct factory connector — no diagnostic coding required. Most engines run a pre-cat (upstream) and a post-cat (downstream) sensor; cross-check your existing part number and the position on the exhaust to make sure you're ordering the right one. Apply a smear of anti-seize compound on the threads before fitting and torque to manufacturer spec. Standard 6 pin connector. Position: Front.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eHow do I know if my lambda sensor is faulty?\u003c\/h4\u003e\n\u003cp\u003eAn OBD2 scan showing P0130-series codes plus poor fuel economy is the clearest sign. Live data showing the sensor stuck at a flat voltage (instead of oscillating between roughly 0.1V and 0.9V) confirms a faulty sensor.\u003c\/p\u003e\n\u003ch4\u003ePre-cat or post-cat — which one do I need?\u003c\/h4\u003e\n\u003cp\u003ePre-cat sensors (upstream of the catalytic converter) control the fuel mixture. Post-cat sensors (downstream) monitor catalyst efficiency. Match the OEM number on your old sensor to the numbers listed above to be sure.\u003c\/p\u003e\n\u003ch4\u003eWill a new sensor fix my fuel economy?\u003c\/h4\u003e\n\u003cp\u003eIf the original sensor is biased lean or rich, a correct replacement typically restores MPG within a tank or two of fuel. Drive at least 20-30 miles after fitting to allow the ECU to re-learn.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283755376984,"sku":"203","price":54.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU203_0258017119_-11_updated_ff16ac83-6151-421a-8c68-8c654338c26e.jpg?v=1781182937"},{"product_id":"new-fuel-high-pressure-sensor-fits-ford-grand-c-max-kuga-20-tdci-9663305480","title":"Fuel Rail Pressure Sensor – Ford Grand C-Max Kuga – 9663305480","description":"\u003cp\u003eRestore correct fuel rail pressure regulation and reliable starting on your Ford Grand C-max Kuga with this direct-replacement fuel pressure sensor — also known as the fuel pressure transducer, high pressure fuel sensor or low pressure fuel sensor. Built to OEM specification and matching part numbers 96.633.054.80, 28497Z01, 9M5Q-9D280-AB, 96.819.096.80 and 6PH1001.1. Also fits equivalent Citroën, Fiat and Peugeot models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283763274072,"sku":"126","price":39.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU126_9663305480-6_updated_3daa211d-bfe5-49aa-912f-6c51ae8d7ddc.jpg?v=1780929282"},{"product_id":"fuel-rail-pressure-sensor-for-ford-focus-iii-10-16-ecoboost-20st-bm5g9f972ba","title":"Fuel Rail Pressure Sensor – Ford Focus III – BM5G9F972BA","description":"\u003cp\u003eGet your Ford Focus III back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the fuel rail pressure sensor or FRP sensor. Built to OEM specification, matching 0261545038, BM5G-9F972-BA, 0261545039, 31339211 and V25-72-0103. Also fits equivalent Volvo models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283763863896,"sku":"130","price":39.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU130_31339211-6_updated_5a394060-c3d1-41d5-910e-7bf42d6a8a8c.jpg?v=1780931756"},{"product_id":"ford-peugeot-citroen-volvo-20-hdi-tdci-fuel-pressure-sensor-high-rail","title":"Fuel Rail Pressure Sensor – Ford Peugeot Citroen Volvo – 55PP0202","description":"\u003cp\u003eGet your Ford back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the low pressure fuel sensor or fuel rail sensor. Built to OEM specification, matching 55PP02-02, 5WS40039, 1570F9 and 1570J3. Also fits equivalent Citroën, Peugeot and Volvo models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Position: Engine Compartment.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283768615256,"sku":"127","price":39.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU127_55PP02-02-9_updated_a982ba8b-90dc-4797-aee0-2e07fd9eabcd.jpg?v=1780929672"},{"product_id":"new-intake-vvt-vanos-solenoid-valve-for-ford-s-max-1516-ecoboost-2011-18","title":"Camshaft Solenoid Valve – Ford S-Max – 2011-2018 – 1319633","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Ford S-max (2011–2018) with this direct-replacement VVT camshaft valve position sensor — also known as the cam timing valve, VVT solenoid or camshaft solenoid. Built to OEM specification and matching part numbers 1319633, 1331496, 1366327, 1793455 and 1871405.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283832807768,"sku":"104","price":43.5,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU104_CN1G6L713AC-6_updated_59b3d34c-552b-4c2e-87fd-cec20836a8fd.jpg?v=1780918627"},{"product_id":"new-camshaft-adjuster-valve-intake-fits-volvo-s40-ii-v50-24t5-31216221-2004-12","title":"Camshaft Solenoid Valve – Volvo S40 II V50 – 2004-2012 – 31216221","description":"\u003cp\u003eReplace your failing VVT camshaft valve position sensor — also called a camshaft phaser solenoid or cam timing valve — on the Volvo S40 II V50 2.4\/t5 (2004–2012) with this OEM-spec direct fit. Matching part numbers 6M5G-6L713-AB, 1478181, 36002687, 31216221 and 381180002. Also fits equivalent Ford models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283833921880,"sku":"109","price":50.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU109_31216221-8_updated_1e11b5bd-e22f-48f3-a943-dd25e02e5bd1.jpg?v=1780920546"},{"product_id":"exhaust-side-vvt-vanos-solenoid-valve-for-ford-focus-iii-16-tilpg-4m5g6l713be","title":"Camshaft Solenoid Valve – Ford Focus III – 4M5G6L713BE","description":"\u003cp\u003eGet your Ford Focus III back to smooth variable valve timing and full engine performance with this replacement VVT camshaft valve position sensor, also referenced in service manuals as the oil control valve (OCV) or vanos solenoid. Built to OEM specification, matching CN1G6L713BC, 6L713BC, 554007, 1319634 and 1331497.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283834347864,"sku":"142","price":46.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU142_CN1G6L713BC-2_updated_2fbbaeea-d4ba-44a7-887b-555c9d357cca.jpg?v=1780940032"},{"product_id":"vvt-vanos-camshaft-adjuster-valve-for-ford-focus-20-st-23-rs-cj5e6b297aa","title":"Camshaft Solenoid Valve – Ford Focus ST RS – CJ5E6B297AA","description":"\u003cp\u003eRestore smooth variable valve timing and full engine performance on your Ford Focus with this direct-replacement VVT camshaft valve position sensor — also known as the camshaft solenoid, oil control valve (OCV) or vanos solenoid. Built to OEM specification and matching part numbers CJ5E-6B297-AA, CJ5Z-6M280-A, CJ5E-6B297-AB, 2026089 and 5146080.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283838968152,"sku":"107","price":48.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU107_CJ5E6B297AA-7_updated_30a3192e-b9ed-40c5-b2dc-6e8afb1031a0.jpg?v=1780919866"},{"product_id":"new-camshaft-adjuster-valve-outlet-fits-volvo-s40-ii-v50-24t5-31216222-2004-12","title":"Camshaft Solenoid Valve – Volvo S40 II V50 – 2004-2012 – 31216222","description":"\u003cp\u003eThis direct-fit VVT camshaft valve position sensor (vanos solenoid \/ variable valve timing solenoid) restores smooth variable valve timing and full engine performance on the Volvo S40 II V50 2.4\/t5 (2004–2012). Built to OEM specification and matching part numbers 6M5G-6L713-BB, 30731282, 31216222, 36002688 and 8692993. Also fits equivalent Ford models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing VVT solenoid or oil control valve typically triggers the check engine light with codes P0010, P0011, P0014 or P0017 (intake\/exhaust camshaft position and actuator circuit faults). Drivers report rough idle, hesitation under acceleration, reduced power, a distinct rattle from the top of the engine on cold start that fades as oil pressure builds, poor fuel economy, and in some cases the vehicle dropping into limp mode. Ignoring the fault can lead to timing chain wear.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The solenoid controls oil flow to the camshaft phaser, so a worn or clogged unit causes the cam timing to lag — producing the symptoms above. Replacement is typically a short job: drain a small amount of oil, undo the retaining bolt, swap the solenoid, refit and clear codes. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0010 or P0011 fault code?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but extended driving with a failed VVT solenoid will accelerate camshaft and timing chain wear because the cam timing is no longer optimised. Replace the solenoid promptly to avoid much costlier repairs.\u003c\/p\u003e\n\u003ch4\u003eDo I need to use OEM oil after fitting?\u003c\/h4\u003e\n\u003cp\u003eUse the engine's specified oil grade and change it on schedule — VVT solenoids fail most often because of dirty or sludged oil. Fresh oil at the correct viscosity is essential.\u003c\/p\u003e\n\u003ch4\u003eWill it fix a rattle on cold start?\u003c\/h4\u003e\n\u003cp\u003eYes, if the rattle is caused by delayed phaser engagement due to a faulty solenoid. If the rattle persists after fitting, the camshaft phaser itself may also need replacement.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283840016728,"sku":"108","price":69.95,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU108_31216222-2_updated_89598b8d-35e9-44b2-87e1-4a9ad59624b2.jpg?v=1780920120"}],"url":"https:\/\/carpartclubs.com\/collections\/ford-kuga-parts.oembed","provider":"CarPartClubs","version":"1.0","type":"link"}