{"title":"Seat Exeo Parts","description":"\u003cp\u003eFind replacement parts for the Seat Exeo — including ride height \u0026amp; level sensors, fuel pressure sensors and fuel pressure regulators. Every part is built to OEM specification and matched to Seat Exeo fitments by part number, so you can order with confidence. We stock 16 Seat Exeo-compatible parts, dispatched from the UK with next-day delivery and a 1-year warranty.\u003c\/p\u003e\u003cp\u003eNot sure if a part fits your Seat Exeo? Send us your registration or VIN and we'll confirm before you order.\u003c\/p\u003e","products":[{"product_id":"8e0907503-air-suspension-ride-height-level-sensor-without-linkage","title":"8E0907503 AIR SUSPENSION RIDE HEIGHT LEVEL SENSOR (WITHOUT LINKAGE)","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi with this direct-replacement ride height level sensor — also known as the headlamp range sensor, suspension level sensor or air suspension sensor. Built to OEM specification and matching part numbers 8E0941285, 8E0941285C, 8E0941285J, 8E0907503 and 6PM008161-50. Also fits equivalent Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283536650584,"sku":"52","price":49.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU52_2_updated_b3b11e78-b1e7-45c4-90d2-e11a0c0ea23d.jpg?v=1780832501"},{"product_id":"front-headlight-level-sensor-for-audi-a4-b6-b7-cabrio-01-09seat-exeo-09-10","title":"Headlight Level Sensor – Front Left \u0026 Right – Audi A4 B6 B7 Cabrio Seat Exeo – 2001-2010 – 8E0941285","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi A4 B6 B7 Cabrio (01-09)seat Exeo with this direct-replacement ride height level sensor — also known as the level sender, height sensor or ride height sensor. Built to OEM specification and matching part numbers 8E0941285, 8E0941285C, 8E0941285J, 8E0907503 and 6PM008161-50. Also fits equivalent Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283542810968,"sku":"4","price":72.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU4_8E0941285J-5_updated_89823b7e-c8cb-4a96-8d1f-2fb9879f8b37.jpg?v=1780746760"},{"product_id":"new-front-headlight-level-height-sensor-fits-audi-a4-b6-b7-2001-09-8e0941285j","title":"Headlight Level Sensor – Front Left \u0026 Right – Audi A4 B6 B7 – 2001-2009 – 8E0941285J","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi A4 B6 B7 (2001–2009) with this direct-replacement ride height level sensor — also known as the suspension level sensor, air suspension sensor or level sender. Built to OEM specification and matching part numbers 8E0941285, 8E0941285C, 8E0941285J, 8E0907503 and 6PM008161-50. Also fits equivalent Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283660022104,"sku":"4","price":64.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU4_8E0941285J-5_updated_44408e05-3165-4fbd-a0da-ec63de3b3b65.jpg?v=1780746788"},{"product_id":"for-audi-seat-skoda-vw-20-tdi-fuel-pump-pressure-regulator-control-0928400706","title":"Fuel Pressure Regulator – Audi Seat Skoda VW – 0928400706","description":"\u003cp\u003eThis direct-fit fuel pressure regulator (fuel pressure control valve \/ FPR) restores correct fuel rail pressure and stable engine running on the Audi. Built to OEM specification and matching part numbers 0928400706, 0928400768, 1462C00987, 0445010507 and 0445010508. Also fits equivalent Volkswagen, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure regulator commonly causes hard starting when hot, rough idle, hesitation under acceleration, poor fuel economy, and fault codes P0089, P0190, P0191 or P0192. On some vehicles you'll see fuel leaks at the regulator body, or a strong fuel smell under the bonnet. Common-rail diesels with stuck regulators drop into limp mode under load. Petrol direct-injection engines may also show a rough cold start or misfire codes.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, threaded into the fuel rail or pump body. Relieve fuel pressure before removal and have rags ready to catch residual fuel. Replace any sealing O-rings supplied. After fitting, cycle the ignition to prime, clear codes and test for leaks before driving. Standard 2 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this the same as a fuel pressure sensor?\u003c\/h4\u003e\n\u003cp\u003eNo — the sensor measures rail pressure and reports to the ECU. The regulator physically controls rail pressure. Both can fail and produce similar fault codes, so confirm with live data before ordering.\u003c\/p\u003e\n\u003ch4\u003eCan I drive with a failing FPR?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but unregulated fuel pressure damages injectors over time on common-rail diesels and causes excess emissions on petrol engines. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eDo I need to code or programme the new regulator?\u003c\/h4\u003e\n\u003cp\u003eNo — it's a passive hydraulic component. The ECU re-learns rail pressure within a few minutes of running.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283702358360,"sku":"245","price":52.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU245_0928400706_-3_updated_94ce79e6-d85a-4ac2-8104-cbeb19577f49.jpg?v=1781458467"},{"product_id":"vw-audi-a3-a4-a5-a6-q5-tt-fuel-pump-pressure-regulator-control-valve-20-tdi","title":"Fuel Pressure Regulator – Audi A3 A4 A5 A6 Q5 TT VW – 0928400706","description":"\u003cp\u003eRestore correct fuel rail pressure and stable engine running on your Volkswagen with this direct-replacement fuel pressure regulator — also known as the FPR, fuel pressure regulator valve or rail pressure regulator. Built to OEM specification and matching part numbers 0928400706, 0928400768, 1462C00987, 0445010507 and 0445010508. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure regulator commonly causes hard starting when hot, rough idle, hesitation under acceleration, poor fuel economy, and fault codes P0089, P0190, P0191 or P0192. On some vehicles you'll see fuel leaks at the regulator body, or a strong fuel smell under the bonnet. Common-rail diesels with stuck regulators drop into limp mode under load. Petrol direct-injection engines may also show a rough cold start or misfire codes.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, threaded into the fuel rail or pump body. Relieve fuel pressure before removal and have rags ready to catch residual fuel. Replace any sealing O-rings supplied. After fitting, cycle the ignition to prime, clear codes and test for leaks before driving.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this the same as a fuel pressure sensor?\u003c\/h4\u003e\n\u003cp\u003eNo — the sensor measures rail pressure and reports to the ECU. The regulator physically controls rail pressure. Both can fail and produce similar fault codes, so confirm with live data before ordering.\u003c\/p\u003e\n\u003ch4\u003eCan I drive with a failing FPR?\u003c\/h4\u003e\n\u003cp\u003eShort distances yes, but unregulated fuel pressure damages injectors over time on common-rail diesels and causes excess emissions on petrol engines. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eDo I need to code or programme the new regulator?\u003c\/h4\u003e\n\u003cp\u003eNo — it's a passive hydraulic component. The ECU re-learns rail pressure within a few minutes of running.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283711172952,"sku":"245","price":52.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU245_0928400706_-3_updated_67f8d16b-b9de-418c-ae9b-5a43bbca900e.jpg?v=1781458529"},{"product_id":"fuel-rail-pressure-sensor-audi-seat-skoda-vw-16-20-tdi-engines-03l906054a","title":"Fuel Rail Pressure Sensor – Audi Seat Skoda VW – 03L906054A","description":"\u003cp\u003eGet your Audi back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the low pressure fuel sensor or fuel rail sensor. Built to OEM specification, matching 03L906054, 85PP2603, 03L906054A, 03L130089B and 03L906051. Also fits equivalent Volkswagen, Skoda and Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283717464408,"sku":"260","price":38.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU260_03L906054A_-_10_updated_4aa8f4fb-e8af-4d84-87c2-0f24172c196b.jpg?v=1781608400"},{"product_id":"fuel-rail-pressure-sensor-for-audi-seat-skoda-vw-16-20-tdi-engines-03l906054a","title":"Fuel Rail Pressure Sensor – Audi Seat Skoda VW – 03L906054A","description":"\u003cp\u003eThis direct-fit fuel pressure sensor (FRP sensor \/ fuel pressure transducer) restores correct fuel rail pressure regulation and reliable starting on the Audi. Built to OEM specification and matching part numbers 03L906054, 85PP26-03, 03L906054A, 03L130089 and 03L130089J. Also fits equivalent Volkswagen, Skoda and Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283718512984,"sku":"260","price":38.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU260_03L906054A_-_10_updated_d97254c6-61b4-415e-b05c-8e10df69cc29.jpg?v=1781608420"},{"product_id":"audi-vw-seat-skoda-fuel-rail-pressure-relief-limiter-valve-057130764h-0281006075","title":"Fuel Pressure Relief Valve – Audi VW Seat Skoda – 057130764H","description":"\u003cp\u003eGet your Audi back to safe fuel pressure relief and reliable cold starting with this replacement fuel pressure relief valve, also referenced in service manuals as the pressure limiter valve or rail pressure relief valve. Built to OEM specification, matching 057130764AB, 057130764H, 0281006075, 04L089D and 057130764. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure relief valve typically causes hard cold starting, prolonged cranking, fault code P008A (low pressure fuel system - pressure too low), and on common-rail diesels the engine dropping into limp mode under load. Drivers often notice fuel pressure dropping rapidly after engine shut-off — the valve fails open, bleeding off the rail's residual pressure between starts.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, threaded into the fuel rail. Relieve fuel pressure before removal. Apply new sealing washers if supplied and torque carefully — over-tightening can crack the rail. After fitting, cycle the ignition to prime, clear codes and verify the rail holds pressure.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this the same as the SCV?\u003c\/h4\u003e\n\u003cp\u003eNo — the SCV regulates fuel entering the pump, while the relief valve protects the rail from over-pressure on the outlet side. Both common-rail components but with different functions.\u003c\/p\u003e\n\u003ch4\u003eWhy does my engine start hot but not cold?\u003c\/h4\u003e\n\u003cp\u003eWhen a relief valve fails open, the rail bleeds pressure overnight. Hot starts succeed because warm fuel vapourises and assists ignition; cold starts fail because there's no residual pressure for the first injection cycle.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it fix my P008A code?\u003c\/h4\u003e\n\u003cp\u003eIf the code points specifically to the relief valve, yes. Some vehicles also throw P008A from SCV faults, so confirm with live pressure data before ordering.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283764027736,"sku":"244","price":92.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU244_0281002859-6_updated_3d38c7c8-e47d-478d-a02f-9b9da17f216d.jpg?v=1781458407"},{"product_id":"high-pressure-petrol-fuel-pump-fits-vw-golf-mk5-1k-20-tfsigti-2004-09-06h12702","title":"High Pressure Fuel Pump – VW Golf Mk5 1K – 2004-2009 – 06H127025N","description":"\u003cp\u003eReplace your failing fuel pump — also called a fuel feed pump or lift pump — on the Volkswagen Golf MK5 1K (2004–2009) with this OEM-spec direct fit. Matching part numbers 06H127025N, 06H127025Q, 06H127025R, 06H127025M and 06H127025P. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pump typically causes the engine to crank but not start, intermittent stalling at speed, loss of power under load (especially uphill), sputtering at high RPM, and a low fuel pressure fault code. Drivers often report a noticeable whining or buzzing from the tank area before the pump finally fails. On modern direct-injection cars, the low-pressure (tank) pump feeds the high-pressure pump — both can fail.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement to the original mounting point — typically inside the fuel tank via the service hatch, or externally on older diesels. Replace the seal\/O-ring on the tank-mounted units as part of the job to avoid leaks. After fitting, cycle the ignition a few times to prime the system before cranking.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eHow do I know if my fuel pump is failing?\u003c\/h4\u003e\n\u003cp\u003eWhining noise from the tank, extended cranking, stalling at speed, and low fuel pressure readings on a diagnostic scan tool are the classic symptoms. A pressure-test gauge connected to the rail gives definitive evidence.\u003c\/p\u003e\n\u003ch4\u003eIs this an in-tank or external pump?\u003c\/h4\u003e\n\u003cp\u003eMatch the OEM number to your existing pump's part number to be sure. Most modern petrol vehicles use in-tank pumps; many older diesels use external lift pumps.\u003c\/p\u003e\n\u003ch4\u003eDo I need to prime the system after fitting?\u003c\/h4\u003e\n\u003cp\u003eCycle the ignition 3–5 times before cranking to allow the new pump to prime the lines. The engine should then start within normal crank time.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283819700568,"sku":"268","price":110.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU268_06H127025N-3_updated_0f5ddd17-c8b6-4e38-b2ff-5c607e5efd46.jpg?v=1781612769"},{"product_id":"fuel-rail-high-pressure-sensor-for-audi-a1-a3-a4-a5-a6-q3-q5-seat-vw-16-20-tdi","title":"Fuel Rail Pressure Sensor – Audi A1 A3 A4 A5 A6 Q3 Q5 Seat VW – 03L906054","description":"\u003cp\u003eGet your Audi A1 A3 A4 A5 A6 Q3 back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the fuel pressure transducer or high pressure fuel sensor. Built to OEM specification, matching 03L906054, 85PP2603, 03L906054A, 03L130089B and 03L906051. Also fits equivalent Volkswagen, Skoda and Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283900473688,"sku":"260","price":38.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU260_03L906054A_-_10_updated_e4d55294-5050-4886-8477-2f9358ecb122.jpg?v=1781608472"},{"product_id":"fuel-rail-high-pressure-sensor-audi-a1-a3-a4-a5-a6-q3-q5-seat-vw-16-20-tdi","title":"Fuel Rail Pressure Sensor – Audi A1 A3 A4 A5 A6 Q3 Q5 Seat VW – 03L906054","description":"\u003cp\u003eGet your Audi A1 A3 A4 A5 A6 Q3 back to correct fuel rail pressure regulation and reliable starting with this replacement fuel pressure sensor, also referenced in service manuals as the low pressure fuel sensor or fuel rail sensor. Built to OEM specification, matching 03L906054, 85PP2603, 03L906054A, 03L130089B and 03L906051. Also fits equivalent Volkswagen, Skoda and Seat models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing fuel pressure sensor commonly logs codes P0190, P0191, P0192, P0193 or P0194 (fuel rail pressure sensor circuit faults). Symptoms include hard starting (hot or cold), prolonged cranking, stalling at idle, hesitation under acceleration, intermittent loss of power, and on common-rail diesels the vehicle dropping into limp mode. A failed sensor can also cause the ECU to default to incorrect injection timing, hurting fuel economy and emissions.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003eDirect-fit replacement, no coding required after fitting. Relieve fuel system pressure before removal (depressurise via the dedicated fuse procedure on most cars). Use a new sealing washer or O-ring if supplied, and torque to manufacturer spec — over-tightening can crack the sensor body. Clear codes with any OBD2 scanner after installation. Standard 3 pin connector.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eCan I drive with a P0190 code?\u003c\/h4\u003e\n\u003cp\u003eShort distances only. A faulty fuel pressure sensor causes incorrect fuelling, which on common-rail diesel engines can damage injectors over time. Replace promptly.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as a fuel pump?\u003c\/h4\u003e\n\u003cp\u003eNo — the pressure sensor measures fuel pressure in the rail and reports it to the ECU. The fuel pump is a separate component that actually moves fuel from the tank. They commonly fail together but are distinct parts.\u003c\/p\u003e\n\u003ch4\u003eDo I need to bleed the fuel system after fitting?\u003c\/h4\u003e\n\u003cp\u003eMost modern cars self-prime when you cycle the ignition. On older common-rail diesels, follow the service-manual bleed procedure to clear air from the high-pressure circuit.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283901194584,"sku":"260","price":38.5,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU260_03L906054A_-_10_updated_5ce1166e-06cb-4592-aa89-e334aec0f263.jpg?v=1781608492"}],"url":"https:\/\/carpartclubs.com\/collections\/seat-exeo-parts.oembed","provider":"CarPartClubs","version":"1.0","type":"link"}