{"title":"Seat Tarraco Parts","description":"\u003cp\u003eFind replacement parts for the Seat Tarraco — including ride height \u0026amp; level sensors. Every part is built to OEM specification and matched to Seat Tarraco fitments by part number, so you can order with confidence. We stock 34 Seat Tarraco-compatible parts, dispatched from the UK with next-day delivery and a 1-year warranty.\u003c\/p\u003e\u003cp\u003eNot sure if a part fits your Seat Tarraco? Send us your registration or VIN and we'll confirm before you order.\u003c\/p\u003e","products":[{"product_id":"5q0512521j-air-suspension-ride-height-level-sensor-for-audi-seat-skoda-vw","title":"Ride Height Sensor – Front Left – Audi Seat Skoda VW – 5Q0512521J","description":"\u003cp\u003eReplace your failing ride height level sensor — also called a height sensor or ride height sensor — on the Audi with this OEM-spec direct fit. Matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283555492184,"sku":"23","price":63.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_6e05b4ca-d84c-4387-acb1-460fa491fe7c.jpg?v=1780778164"},{"product_id":"audi-a3-8v1-8va-8vm-front-right-suspension-height-sensor-2012-5q0412522c","title":"Ride Height Sensor – Front Right – Audi A3 8V1 8VA 8VM – 2012-on – 5Q0412522C","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi A3 8V1 8VA 8VM with this direct-replacement ride height level sensor — also known as the headlamp range sensor, suspension level sensor or air suspension sensor. Built to OEM specification and matching part numbers 5Q0412522C, 5Q0412522, 5Q0907503, 3Q0412522A and 5Q0512522. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283555557720,"sku":"2","price":59.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU2_5Q0412522C-4_updated_007dd6fe-5503-4023-9d5b-ea9af2d25cbf.jpg?v=1780746478"},{"product_id":"5q0412521c-air-suspension-ride-height-level-sensor-for-audi-seat-skoda-vw","title":"Ride Height Sensor – Front Left – Audi Seat Skoda VW – 5Q0412521C","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi with this direct-replacement ride height level sensor — also known as the headlamp range sensor, suspension level sensor or air suspension sensor. Built to OEM specification and matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283555590488,"sku":"40","price":63.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU40_s-l1600_1_updated_df10cc13-1807-453b-a1fc-1074e60f5a61.jpg?v=1780781972"},{"product_id":"3q0412521a-air-suspension-ride-height-level-sensor-for-seat-skoda-vw","title":"Ride Height Sensor – Front Left – Seat Skoda VW – 3Q0412521A","description":"\u003cp\u003eThis direct-fit ride height level sensor (level sender \/ height sensor) restores proper headlight beam alignment and air suspension control on the Seat. Built to OEM specification and matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Audi, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283555787096,"sku":"16","price":63.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU16_s-l1600_6_updated_8d58d15b-00d9-428e-bc86-a35c255d731a.jpg?v=1780755118"},{"product_id":"front-right-suspension-height-sensor-for-seat-leon-5q0412522c-oem-quality","title":"Ride Height Sensor – Front Right – Seat Leon – 5Q0412522C","description":"\u003cp\u003eThis direct-fit ride height level sensor (headlight level sensor \/ headlamp range sensor) restores proper headlight beam alignment and air suspension control on the Seat Leon. Built to OEM specification and matching part numbers 5Q0412522C, 5Q0412522, 5Q0907503, 3Q0412522A and 5Q0512522. Also fits equivalent Audi, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283572531544,"sku":"2","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU2_5Q0412522C-4_updated_a3a4540a-4e02-471c-a4f8-60db626fc178.jpg?v=1780746508"},{"product_id":"front-right-suspension-height-sensor-for-audi-a3-q2-q3-5q0412522c-oem-quality","title":"Ride Height Sensor – Front Right – Audi A3 Q2 Q3 – 5Q0412522C","description":"\u003cp\u003eGet your Audi A3 Q2 Q3 back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the level sender or height sensor. Built to OEM specification, matching 5Q0412522C, 5Q0412522, 5Q0907503, 3Q0412522A and 5Q0512522. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283572564312,"sku":"2","price":59.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU2_5Q0412522C-4_updated_712e5c14-8f8b-4f54-bc59-03c1d9e42254.jpg?v=1780746536"},{"product_id":"audi-a3-2012-on-front-left-suspension-height-sensor-oem-5q0412521c-8v1-8va-8vm","title":"Ride Height Sensor – Front Left – Audi A3 8V1 8VA 8VM – 2012-on – 5Q0412521C","description":"\u003cp\u003eGet your Audi A3 2012-On (2012 onwards) back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the headlight level sensor or headlamp range sensor. Built to OEM specification, matching 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283576693080,"sku":"40","price":47.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU40_s-l1600_1_updated_71e81821-21cd-4c23-8a75-6969e3db4945.jpg?v=1780782118"},{"product_id":"air-suspension-audi-a3-ride-height-level-sensor-offside-front-3q0412522a-2012-on","title":"Ride Height Sensor – Front Right – Audi A3 – 2012-on – 3Q0412522A","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi A3 Ride (2012 onwards) with this direct-replacement ride height level sensor — also known as the ride height sensor, headlight level sensor or headlamp range sensor. Built to OEM specification and matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283578003800,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_a8580113-3b24-4f50-9bb7-776859a7e42f.jpg?v=1780778797"},{"product_id":"seat-leon-5f1-5f5-5f8-rear-left-height-level-sensor-2012-2020-oem-5q0512521j","title":"Ride Height Sensor – Rear Left – Seat Leon 5F1 5F5 5F8 – 2012-2020 – 5Q0512521J","description":"\u003cp\u003eGet your Seat Leon 5F1 5F5 5F8 (2012–2020) back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the air suspension sensor or level sender. Built to OEM specification, matching 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Audi, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283578429784,"sku":"23","price":59.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_e9f5b251-2107-413a-83eb-c2a53b8a8ec3.jpg?v=1780778182"},{"product_id":"air-suspension-vw-t-roc-ride-height-level-sensor-offside-front-3q0412522a-17-on","title":"Ride Height Sensor – Front Right – VW T-Roc – 2017-on – 3Q0412522A","description":"\u003cp\u003eReplace your failing ride height level sensor — also called a ride height sensor or headlight level sensor — on the Volkswagen T-roc Ride with this OEM-spec direct fit. Matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283648848216,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_225fca5d-ef2f-48cb-935a-701f8a1d3017.jpg?v=1780778810"},{"product_id":"air-suspension-vw-touran-ride-height-level-sensor-offside-front-3q0412522a-15-on","title":"Ride Height Sensor – Front Right – VW Touran – 2015-on – 3Q0412522A","description":"\u003cp\u003eGet your Volkswagen Touran Ride back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the headlamp range sensor or suspension level sensor. Built to OEM specification, matching 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283648946520,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_7f1766f2-6753-40c4-8c31-1b2ee027ca29.jpg?v=1780778825"},{"product_id":"air-suspension-vw-tiguan-allspace-ride-height-level-sensor-offside-front-3q04125","title":"Ride Height Sensor – Front Right – VW Tiguan Allspace – 3Q0412522A","description":"\u003cp\u003eThis direct-fit ride height level sensor (level sender \/ height sensor) restores proper headlight beam alignment and air suspension control on the Volkswagen Tiguan Allspace Ride. Built to OEM specification and matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503, 5Q0412522C and 3Q04125. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283649012056,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_cf90e76f-0ae7-4918-a246-fd451ac4971b.jpg?v=1780778838"},{"product_id":"air-suspension-vw-tiguan-ride-height-level-sensor-offside-front-3q0412522a-16-on","title":"Ride Height Sensor – Front Right – VW Tiguan – 2016-on – 3Q0412522A","description":"\u003cp\u003eThis direct-fit ride height level sensor (level sender \/ height sensor) restores proper headlight beam alignment and air suspension control on the Volkswagen Tiguan Ride. Built to OEM specification and matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283649044824,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_d2ac26c1-66f8-4666-8565-71da660ff324.jpg?v=1780778853"},{"product_id":"air-suspension-vw-golf-ride-height-level-sensor-offside-front-3q0412522a","title":"Ride Height Sensor – Front Right – VW Golf – 3Q0412522A","description":"\u003cp\u003eThis direct-fit ride height level sensor (level sender \/ height sensor) restores proper headlight beam alignment and air suspension control on the Volkswagen Golf Ride. Built to OEM specification and matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283651371352,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_0578cb80-4cef-4350-9cbd-37a18ffad3d8.jpg?v=1780778866"},{"product_id":"air-suspension-skoda-kodiaq-ride-height-level-sensor-offside-front-3q0412522a","title":"Ride Height Sensor – Front Right – Skoda Kodiaq – 3Q0412522A","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Skoda Kodiaq Ride with this direct-replacement ride height level sensor — also known as the headlamp range sensor, suspension level sensor or air suspension sensor. Built to OEM specification and matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Seat and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283651535192,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_4282c46b-d047-4edb-bc13-3cc467a0d270.jpg?v=1780778879"},{"product_id":"air-suspension-skoda-octavia-ride-height-level-sensor-offside-front-3q0412522a","title":"Ride Height Sensor – Front Right – Skoda Octavia – 3Q0412522A","description":"\u003cp\u003eGet your Skoda Octavia Ride back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the headlamp range sensor or suspension level sensor. Built to OEM specification, matching 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Seat and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283651600728,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_0fe460fe-e249-46c1-9f09-7d76cb752c2b.jpg?v=1780778894"},{"product_id":"air-suspension-seat-tarraco-ride-height-level-sensor-offside-front-3q0412522a","title":"Ride Height Sensor – Front Right – Seat Tarraco – 3Q0412522A","description":"\u003cp\u003eReplace your failing ride height level sensor — also called a headlamp range sensor or suspension level sensor — on the Seat Tarraco Ride with this OEM-spec direct fit. Matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283652845912,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_49ad8cbc-077f-4310-a52e-661049a67c78.jpg?v=1780778908"},{"product_id":"air-suspension-seat-leon-st-ride-height-level-sensor-offside-front-3q0412522a","title":"Ride Height Sensor – Front Right – Seat Leon ST – 3Q0412522A","description":"\u003cp\u003eReplace your failing ride height level sensor — also called an air suspension sensor or level sender — on the Seat Leon ST Ride with this OEM-spec direct fit. Matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283652878680,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_3957601e-72c6-4552-b022-5c00ab28fbcc.jpg?v=1780778921"},{"product_id":"air-suspension-seat-leon-ride-height-level-sensor-offside-front-3q0412522-2012-o","title":"Ride Height Sensor – Front Right – Seat Leon – 2012-on – 3Q0412522A","description":"\u003cp\u003eGet your Seat Leon Ride back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the air suspension sensor or level sender. Built to OEM specification, matching 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Audi, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283652911448,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_e30e3d2e-2d60-46fe-984b-93d1f310b380.jpg?v=1780778933"},{"product_id":"air-suspension-audi-q3-ride-height-level-sensor-offside-front-3q0412522a-2018-on","title":"Ride Height Sensor – Front Right – Audi Q3 – 2018-on – 3Q0412522A","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Audi Q3 Ride (2018 onwards) with this direct-replacement ride height level sensor — also known as the height sensor, ride height sensor or headlight level sensor. Built to OEM specification and matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283653075288,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_108263a5-b6e3-401a-9261-d0c0afa98ca1.jpg?v=1780778949"},{"product_id":"air-suspension-audi-q2-ride-height-level-sensor-offside-front-3q0412522a-2016-on","title":"Ride Height Sensor – Front Right – Audi Q2 – 2016-on – 3Q0412522A","description":"\u003cp\u003eReplace your failing ride height level sensor — also called a suspension level sensor or air suspension sensor — on the Audi Q2 Ride (2016 onwards) with this OEM-spec direct fit. Matching part numbers 3Q0412522, 3Q0412522A, 5Q0907503 and 5Q0412522C. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283653173592,"sku":"25","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU25_3_updated_08f208f3-cf4c-4165-ac01-3e96f4bef8f7.jpg?v=1780778962"},{"product_id":"air-level-sensor-vw-golf-hybrid-gte-alltrack-5q0412521c-5q0512521f-3q0412521a","title":"Ride Height Sensor – Front Left – VW Golf – 5Q0412521C","description":"\u003cp\u003eThis direct-fit ride height level sensor (headlight level sensor \/ headlamp range sensor) restores proper headlight beam alignment and air suspension control on the Volkswagen Golf. Built to OEM specification and matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283653894488,"sku":"23","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_7c2bc35a-b9ec-4089-89a8-0437b88a3d6f.jpg?v=1780778197"},{"product_id":"air-ride-height-sensor-audi-vw-seat-skoda-5q0412521c-5q0512521f-5q0512521j","title":"Ride Height Sensor – Front Left – Audi VW Seat Skoda – 5Q0412521C","description":"\u003cp\u003eReplace your failing ride height level sensor — also called a suspension level sensor or air suspension sensor — on the Audi with this OEM-spec direct fit. Matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283653927256,"sku":"23","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_f3150c21-4ea4-4367-b294-36d7500612c8.jpg?v=1780778212"},{"product_id":"air-suspension-ride-height-level-sensor-fits-skoda-octavia-kodiaq-suv-estate","title":"Ride Height Sensor – Front Left – Skoda Octavia Kodiaq – 5Q0412521C","description":"\u003cp\u003eThis direct-fit ride height level sensor (suspension level sensor \/ air suspension sensor) restores proper headlight beam alignment and air suspension control on the Skoda Octavia Kodiaq. Built to OEM specification and matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Audi, Seat and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283654582616,"sku":"23","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_571d5095-b7da-4ae5-8215-0f18999b7105.jpg?v=1780778228"},{"product_id":"air-suspension-height-level-sensor-fits-vw-golf-tiguan-touran-t-roc-estate-suv","title":"Ride Height Sensor – Front Left – VW Golf Tiguan Touran T-Roc – 5Q0412521C","description":"\u003cp\u003eRestore proper headlight beam alignment and air suspension control on your Volkswagen Golf Tiguan Touran T-roc with this direct-replacement ride height level sensor — also known as the headlamp range sensor, suspension level sensor or air suspension sensor. Built to OEM specification and matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283654746456,"sku":"23","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_36d9e19e-2f0a-49dd-9924-b598d009864b.jpg?v=1780778245"},{"product_id":"air-suspension-ride-height-level-sensor-fits-audi-a3-q2-q3-suv-hatchback-4-pin","title":"Ride Height Sensor – Front Left – Audi A3 Q2 Q3 – 5Q0412521C","description":"\u003cp\u003eGet your Audi A3 Q2 Q3 back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the suspension level sensor or air suspension sensor. Built to OEM specification, matching 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283654844760,"sku":"23","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU23_23_4_updated_ad9a1c10-479b-434c-af55-e40a50f5294e.jpg?v=1780778262"},{"product_id":"air-suspension-height-level-sensor-front-left-for-audi-a3-q2-q3-5q0412521c","title":"Ride Height Sensor – Front Left – Audi A3 Q2 Q3 – 5Q0412521C","description":"\u003cp\u003eThis direct-fit ride height level sensor (headlight level sensor \/ headlamp range sensor) restores proper headlight beam alignment and air suspension control on the Audi A3 Q2 Q3. Built to OEM specification and matching part numbers 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283694952792,"sku":"40","price":44.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU40_s-l1600_1_updated_95ed875d-7081-40bd-83d2-82744cfb6bb7.jpg?v=1780782142"},{"product_id":"front-left-headlight-level-sensor-for-audi-a3-s3-2012-vw-golf-5q0412521c-4pin","title":"Headlight Level Sensor – Front Left – Audi A3 S3 VW Golf – 2012-on – 5Q0412521C","description":"\u003cp\u003eGet your Audi A3 S3 2012– back to proper headlight beam alignment and air suspension control with this replacement ride height level sensor, also referenced in service manuals as the ride height sensor or headlight level sensor. Built to OEM specification, matching 5Q0412521, 5Q0412521C, 5Q0907503, 3Q0412521A and 5Q0512521F. Also fits equivalent Seat, Skoda and Volkswagen models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Left.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283695116632,"sku":"40","price":44.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU40_s-l1600_1_updated_c921e939-62a0-4005-8fbb-1b4cde14a113.jpg?v=1780782168"},{"product_id":"front-right-height-level-sensor-for-vw-arteon-golf-mk7-passat-b8-5q0412522c","title":"Ride Height Sensor – Front Right – VW Arteon Golf Mk7 Passat B8 – 5Q0412522C","description":"\u003cp\u003eThis direct-fit ride height level sensor (air suspension sensor \/ level sender) restores proper headlight beam alignment and air suspension control on the Volkswagen Arteon Golf MK7 Passat B8. Built to OEM specification and matching part numbers 5Q0412522C, 5Q0412522, 5Q0907503, 3Q0412522A and 5Q0512522. Also fits equivalent Audi, Seat and Skoda models.\u003c\/p\u003e\n\u003ch3\u003eCommon signs of failure\u003c\/h3\u003e\n\u003cp\u003eA failing ride height sensor commonly causes xenon, LED or matrix headlights to point too high (dazzling oncoming drivers) or too low (reducing your night-time visibility), and often disables auto-levelling entirely. On VAG group cars expect dashboard headlight error messages and fault codes B106A or B107A; on cars with air suspension you'll see the suspension warning light, uneven ride height, or the vehicle stuck low after parking. Faulty sensors also cause MOT fails on the headlamp aim test.\u003c\/p\u003e\n\u003ch3\u003eFitment notes\u003c\/h3\u003e\n\u003cp\u003ePlug-and-play installation, no diagnostic coding required. The same physical sensor is shared across the VAG group (Audi, VW, Skoda, Seat) on many platforms — the quickest way to confirm fit is to match your existing part number to one of those listed above. Mounting bracket and linkage are typically reused from your original sensor. Standard 4 pin connector. Position: Front, Right.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eIs this a headlight sensor or an air suspension sensor?\u003c\/h4\u003e\n\u003cp\u003eSame physical part — most VAG group cars use one sensor whose signal feeds both the auto-levelling headlight ECU and (where fitted) the air suspension control module. Replacing it fixes both systems.\u003c\/p\u003e\n\u003ch4\u003eWill replacing it stop the dashboard warning?\u003c\/h4\u003e\n\u003cp\u003eYes — once the new sensor is fitted and the ignition cycled, headlight error messages usually clear on their own. Stubborn faults can be cleared with VCDS or any generic OBD2 scanner that supports module reset.\u003c\/p\u003e\n\u003ch4\u003eDo I need to calibrate the headlamps after fitting?\u003c\/h4\u003e\n\u003cp\u003eBasic aim adjustment is recommended after replacement; full electronic calibration is only required if the headlamp unit itself was also replaced.\u003c\/p\u003e","brand":"PitShopUK","offers":[{"title":"Default Title","offer_id":57283849584984,"sku":"2","price":62.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0947\/3373\/0136\/files\/SKU2_5Q0412522C-4_updated_cb354660-20d3-456a-8964-e5d763df8e80.jpg?v=1780746567"}],"url":"https:\/\/carpartclubs.com\/collections\/seat-tarraco-parts.oembed","provider":"CarPartClubs","version":"1.0","type":"link"}